OTe 25/220…240/700 PC
Product family benefits
- Compact housing for mounting in very tight spaces
- Compatible with the most common leading-edge and trailing-edge phase dimmers
Areas of application
- Optional cable clamp E-style for independent mounting
- Suitable for indoor installations
- Suitable for indoor SELV installations
Technical Data
Electrical data
Nominal input voltage
220…240 V
Mains frequency
50/60 Hz
Input voltage AC
198…264 V
Total harmonic distortion
15 %
Power factor λ
0.90C…0.98
Efficiency in full-load
86 %
Device power loss
3,9 W
Inrush current
7 A
Max. ECG no. on circuit breaker 10 A (B)
41
Max. ECG no. on circuit breaker 16 A (B)
65
Max. ECG no. on circuit breaker 25 A (B)
-
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
18…36 V
U-OUT (working voltage)
50 V
Nominal output current
700 mA
Output current tolerance
±10 %
Output ripple current (100 Hz)
< 35 %
Output PSTLM
≤1
Output SVM
≤0.8
Nominal output power
25 W
Maximum output power
25 W
Galvanic isolation primary/secondary
SELV
Current set
Fixed current
Dimensions & weight
Mounting hole spacing, length
-
Mounting hole spacing, width
-
Product weight
93.00 g
Cable cross-section, input side
0.75…1.5 mm²
Cable cross-section, output side
0.5…1.5 mm²
Wire preparation length, input side
8.0…9.0 mm
Wire preparation length, output side
8.0…9.0 mm
Height
30.0 mm
Length
95.0 mm
Width
53.0 mm
Colors & materials
Casing material
Plastic
Temperatures & operating conditions
Ambient temperature range
-20…+50 °C
Maximum temperature at tc test point
75 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-25…75 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
50000 h
Capabilities
Dimmable
Yes
Dimming interface
Phase Cut
Dimming range
10…100 %
Dimming method
Amplitude Modulation
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I / II
Type of connection, output side
Push terminal
Suitable for through-wiring
No
Certificates & standards
Approval marks – approval
CE / ENEC 10 / VDE / CB
Standards
Acc. to EN 61347-1/Acc. to EN 61347-2-13/Acc. to EN 62384/Acc. to CISPR 15/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 61347
Protection class
II
Type of protection
IP20
Logistical data
Commodity code
85044083900
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
05-05-2023
Primary Article Identifier
4052899105386
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
0324db9a-533b-47ff-ad8f-ecaea5912679
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4052899105386 |
UNV
| 1 | 95mm x 53mm x 30mm | 93.00g | 0.15dm³ |
| 4052899105393 |
VS
| 20 | 284mm x 207mm x 100mm | 2138.00g | 5.88dm³ |
Downloads
Data sheets
Accessories optional
Information about Family
Constant Current SELV drivers with leading- or trailing-edge dimming.
The compatibility with the most common leading-edge and trailing-edge phase dimmers and the possibility of 10…100% dimming pose some key benefits of this product. It can be used for SELV installations and the optional cable clamp enables independent installations.
The compatibility with the most common leading-edge and trailing-edge phase dimmers and the possibility of 10…100% dimming pose some key benefits of this product. It can be used for SELV installations and the optional cable clamp enables independent installations.
Product family features
- Dimmable via leading edge/trailing edge
- Type of protection: IP20
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
OTe 10/220…240/700 PC
|
7…14 V | 700 mA | 95.0 mm | 53.0 mm | 25.0 mm | ||
|
OTe 13/220…240/350 PC
|
18…38 V | 350 mA | 95.0 mm | 53.0 mm | 25.0 mm | ||
|
OTe 18/220…240/500 PC
|
18…36 V | 500 mA | 95.0 mm | 53.0 mm | 30.0 mm | ||
|
OTe 18/220…240/350 PC
|
27…54 V | 350 mA | 95.0 mm | 53.0 mm | 30.0 mm | ||
|
|
OTe 25/220…240/700 PC
|
18…36 V | 700 mA | 95.0 mm | 53.0 mm | 30.0 mm |