OTI DX 100/220...240/700 D NFC IND L
.jpg)
.jpg)
Product family benefits
- Versatile non-isolated DEXAL LED driver up to 150 W due to flexible output characteristic
- Integrated DEXAL Bus power supply for sensors and wireless radios
- Simplified luminaire design for wireless lighting control system and sensors
- Locking and unlocking of luminaire/driver data
- Advanced luminaire/driver data (power, energy, operating hours…) for analytics
- Prepared for DiiA Specification Parts -250, -251, -252 and -253
- Fully programmable via T4T software (NFC, DALI Interface)
- Lifetime: up to 100,000 h (temperature at Tc = 75 °C, max. 10 % failure rate)
- High light quality: 1…100% amplitude dimming and <1% output ripple current
- Wide operating temperature range: -40…+65 °C
- High surge protection: up to 4 kV (L-N) / 4 kV (L/N-PE)
- Integrated inrush current limiter
- Very high efficiency (up to 96%)
Areas of application
- Linear and area lighting
- Industry lighting
- Suitable for luminaires of protection class I
Technical Data
Electrical data
Nominal input voltage
220…240 V
Mains frequency
0/50/60 Hz
Input voltage AC
198…264 V
Input voltage DC
176…276 V
Current set
NFC / LEDset / Programmable
Total harmonic distortion
< 10 %
Power factor λ
0.57C…0.98
Efficiency in full-load
93 %
Device power loss
2.0 W
Inrush current
≤ 5 A
Max. ECG no. on circuit breaker 10 A (B)
20
Max. ECG no. on circuit breaker 10 A (C)
-
Max. ECG no. on circuit breaker 16 A (C)
-
Max. ECG no. on circuit breaker 16 A (B)
32
Max. ECG no. on circuit breaker 25 A (B)
-
Surge capability (L/N-Ground)
4 kV
Surge capability (L-N)
4 kV
Nominal output voltage
64…300 V
U-OUT (working voltage)
< 310 V
Nominal output current
200…700 mA
Output current LEDset open
100 mA
Output current LEDset shorted
200 mA
Default output current
100 mA
Output current tolerance
±3 %
Output ripple current (100 Hz)
< 1 %
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
23…100 W
Maximum output power
100 W
Galvanic isolation
Non isolated
DEXAL Guaranteed Supply Current
53 mA
DEXAL Supply Voltage
15 V
DEXAL Peak Supply Current
60 mA
Power loss in stand-by mode
<0.25 W
Dimensions & weight
Mounting hole spacing, length
414.0 mm
Product weight
311.13 g
Cable cross-section, input side
0.5…1.5 mm²
Cable cross-section, output side
0.5…1.5 mm²
Wire preparation length, input side
8.0…9.0 mm
Wire preparation length, output side
8.0…9.0 mm
Height
21.0 mm
Length
425.0 mm
Width
30.0 mm
Colors & materials
Casing material
Metal
Temperatures & operating conditions
Ambient temperature range
-40…+70 °C
Maximum temperature at tc test point
85 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-40…+85 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
100000 / 50000 h
Additional product data
Encapsulated
No
Capabilities
Programming interface
DEXAL, NFC, LEDset
Dimmable
Yes
Dimming interface
DALI-2 / DEXAL
Dimming range
1…100 %
Dimming method
Full analogue dimming / AM/PWM selectable
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I
Suitable for emergency lighting
Yes
Type of connection, input side
Push terminal
Type of connection, output side
Push terminal
DALI-2 Diagnostic Data
Yes
Constant lumen function
Programmable
DALI-2 Energy Data
Yes
Control interface
DEXAL
Number of channels
1
Programming
Programming device
DALI magic / NFC Scanner
Tuner4TRONIC
Yes
Tuner4TRONIC Field App
Yes
Box programming
Yes
Programmable features
DALI-2 Luminaire Data
Yes
DEXAL Power Supply Unit
Yes
Certificates & standards
Approval marks – approval
CE / EL / VDE-ENEC / VDE-EMC / EAC / CCC / BIS / RCM
Standards
Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to IEC 62386/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
Type of protection
IP20
Logistical data
Commodity code
85044083900
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
20-11-2023
Primary Article Identifier
4062172050883
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
138efd98-9890-461a-92c7-9259550af640
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4062172050883 |
UNV
| 1 | 425mm x 30mm x 21mm | 311.00g | 0.27dm³ |
| 4062172050890 |
VS
| 20 | 447mm x 160mm x 101mm | 6421.00g | 7.22dm³ |
Downloads
Data sheets
Accessories optional
Information about Family
Future proof – ready for intelligent, efficient and robust industry solutions.
The DEXAL Interface and the DiiA -250 as well as an integrated DiiA -251, -252, -253 for luminaire info and monitoring data present one key characteristic of this LED Driver. Additionally the module is fully digitally programmable by DALI, NFC and LT2 and contains very wide operating windows up to 600mA.
The DEXAL Interface and the DiiA -250 as well as an integrated DiiA -251, -252, -253 for luminaire info and monitoring data present one key characteristic of this LED Driver. Additionally the module is fully digitally programmable by DALI, NFC and LT2 and contains very wide operating windows up to 600mA.
Product family features
- Line frequency: 0 Hz | 50 Hz | 60 Hz
- Versatile scope of application due to output power range of up to 150 W
- Monitoring of luminaire operating parameters
- Supply voltage: 220…240 V
- Available with output current range: up to 850 mA
- Constant Lumen Output (CLO)
- Integrated customizable thermal management (Driver Guard)
- Non-isolated drivers
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
|
OTI DX 100/220...240/700 D NFC IND L
|
64…300 V | 200…700 mA | 425.0 mm | 30.0 mm | 21.0 mm | ||
|
OTI DX 150/220...240/850 D NFC IND L
|
64…300 V | 250…850 mA | 425.0 mm | 30.0 mm | 21.0 mm |